When ultimate protection is required, only one classified asset will do: BondX — 9H Pro Ceramic Coating. Engineered for operatives who demand maximum defense, BondX forms a permanent 9H-rated shield against UV rays, chemicals, contaminants, and scratches.
This isn’t just a coating — it’s mission armor. With a durability measured in years (not weeks), BondX ensures your paint, carbon fiber, trim, and wheels remain mission-ready with an impenetrable gloss finish.
Why Deploy BondX 9H Pro Ceramic Coating?
Compared to detail sprays or short-term protectants, BondX offers:
- 9H Hardness Shield — resists scratches, swirls, and micro-marring.
- Extreme Hydrophobic Defense — instant water beading and self-cleaning effect.
- UV & Chemical Resistance — prevents fading, oxidation, and etching.
- Long-Term Durability — protection measured in years.
- High-Gloss Finish — creates unmatched depth and reflective shine.
BondX is the classified solution for vehicles requiring maximum long-term defense.
Classified Specs: BondX 9H Pro Ceramic Coating
- ✅ 9H hardness rating for maximum protection
- ✅ Long-term durability (5-7+ years with proper care)
- ✅ Hydrophobic, self-cleaning properties
- ✅ Resistant to UV rays, bird droppings, tree sap, road salts, and harsh chemicals
- ✅ Mirror-like gloss and depth enhancement
- ✅ Safe for paint, glass, trim, and wheels
Deployment Protocol: How to Apply BondX Ceramic Coating
Follow these mission steps carefully — precision matters.
1. Prep the Surface (Critical Phase)
- Wash the vehicle thoroughly.
- Decontaminate with clay bar or clay towel and our OxydX - Iron Remover.
- Perform paint correction if necessary — BondX locks in whatever condition the surface is in.
2. Panel Wipe / Surface Cleanse
- Use our StrypX - Surface Spray to remove oils, waxes, and residues.
- Ensure the surface is 100% clean for maximum bonding.
3. Controlled Application
- Shake BondX well.
- Using an applicator pad and apply a few drops of BondX.
- Work in small sections (2’x2’). Wipe in crosshatch patterns (up/down, then side/side).
4. Flash & Level
- Allow the coating to flash (typically 5–15 seconds depending on temperature/humidity).
- Using a clean microfiber towel, gently level and buff the surface to remove any high spots.
5. Repeat Panel by Panel
- Continue across the entire vehicle, ensuring even coverage.
- Replace applicator pad if they become saturated or hardened
6. Cure Time
- Allow BondX to cure undisturbed for at least 12–24 hours in a dry environment.
- Avoid water contact for 48 hours. Full cure is achieved in 5–7 days.
6. Additional Layers
- If applying an additional layer, wait 2 hours between layers.
Mission Outcome: Results You Can Expect
After applying BondX 9H Pro Ceramic Coating, your vehicle will be:
✅ Armored with a permanent 9H shield against scratches and contaminants.
✅ Immune to UV rays, water spots, sap, and harsh chemicals.
✅ Enhanced with a deep, mirror-like gloss that outshines standard coatings.
✅ Easier to clean with the hydrophobic self-cleaning effect.
Pro Tips from Command
- Work indoors or in a controlled environment for best results.
- Always use fresh microfiber towels to avoid streaking or high spots.
- Layering is possible — apply a second coat after 2 hours for maximum durability.
- Maintain with pH-neutral soaps like pHoamX and boost gloss with CeramX.
Final Debrief
When the mission calls for elite-level, long-term defense, nothing matches the classified strength of BondX — 9H Pro Ceramic Coating. With years of durability, maximum gloss, and an impenetrable shield, BondX is the ultimate protection upgrade in the Operator’s Portal.
👉 Deploy BondX 9H Pro Ceramic Coating Now in the Operator’s Portal
Leave a comment
All comments are moderated before being published.
This site is protected by hCaptcha and the hCaptcha Privacy Policy and Terms of Service apply.